How to Replace the  Printhead on Your Lancelot M1630 Pro DTF Printer

How to Replace the Printhead on Your Lancelot M1630 Pro DTF Printer

How to Replace the Printhead on Your Lancelot M1630 Pro DTF Printer

Technical Operating Procedure & Maintenance Manual | Lancelot M1630 Pro Series

ABSTRACT & OVERVIEW

Replacing a DTF printhead requires more than removing the old component and installing a new one. Proper preparation, careful handling, and correct connections are essential to protect your new printhead. In this guide, we'll walk you through 4 essential steps for replacing the printhead on your Lancelot M1630 Pro, along with common installation problems to avoid.

Section I. Prepare the Printer

Before starting the replacement, contact Lancelot technical support and follow the technician's instructions throughout the process. You can also refer to the accompanying video tutorial.

IMPORTANT: Clean the White Ink System First

Before removing the old printhead, complete the following preparation:

  1. Empty the old white ink from the cartridge.
  2. Thoroughly clean the inner walls of the cartridge with water.
  3. Refill the cartridge with purified water.
  4. Use a syringe to flush the white ink tubes and dampers until they are completely clean.

Make sure the white ink system is thoroughly cleaned before proceeding.

Warning: Next, turn off the printer and unplug the power cable. Never remove or install a printhead while the printer is connected to power.

Section II. Remove the Old Printhead

Follow these steps to remove the old printhead:

  • Move the printhead bracket: Turn the black knob counterclockwise and move the printhead bracket to the center position.
  • Remove the cover and cable plate: Remove the cover, loosen the screws, and take off the black metal plate securing the printhead cables.
  • Disconnect the cables: Gently pull the two printhead cables out horizontally. Avoid pulling or bending them forcefully.
  • Remove the dampers: Take the dampers off the printhead and place them in a plastic bag.
  • Loosen the printhead screws: Remove the four screws around the printhead to release it from the bracket.
CRITICAL SAFETY: Protect the Nozzle Surface

The bottom nozzle surface is delicate and must be handled carefully.

  • Never touch the nozzle surface with your fingers.
  • Do not allow it to come into contact with any object.
  • After removing the printhead, keep the nozzle surface facing upward and suspended.

Improper handling may damage the nozzle surface. Take extra care throughout the removal process.

Section III. Install the New Printhead

After removing the old printhead, prepare the replacement for installation.

  1. Align the new printhead with its designated position.
  2. Insert it into the printhead bracket.
  3. Tighten the four fixing screws to secure it in place.
  4. Make sure the printhead is properly positioned before proceeding with the ink and cable connections.

Prepare and Refill the Ink

Before adding white ink to the cartridge, shake the fresh ink bottle for at least five minutes.

We highly recommend using a fresh bottle of white ink. Older white ink may contain significant sediment, which can be harmful to a new printhead.

Next, reinstall the dampers:

  • Install each damper according to its corresponding color.
  • Make sure each damper is properly positioned.
  • Use a syringe to draw ink through each damper until it is completely filled.

The extracted white ink can be refilled into the corresponding color ink cartridge at the back of the printer.

Prepare tissues in case ink leaks during the process. When switching between different colors, clean the syringe connector before using it again to avoid mixing ink.

Connect the Printhead Cables Correctly

Pay close attention to the cable positions and contact directions:

Cable Identifier Slot & Orientation Specification
Left Cable Lower slot (contacts facing down)
Right Cable Upper slot (contacts facing up)

Align each cable with its corresponding adapter-board slot. Insert the cables slowly and straight, a little at a time.

Never force a cable into its slot. The pins are delicate and can be damaged easily if the cable is inserted incorrectly or with excessive force.

Keep all liquid away from the electrical connectors throughout the installation process. After connecting both cables correctly, reinstall the screws and the black metal plate that secures them.

Section IV. Perform the Post-Installation Inspection

Once the installation is complete, return the printhead bracket to the capping station. Reconnect the power supply and turn on the printer.

Before normal printing, complete the following inspection:

  • Load the ink: Use the ink-loading function in the printing software.
  • Move the printhead bracket: Move the bracket to the middle position.
  • Check the ink pad: Inspect whether there is ink on the ink pad.

Follow the appropriate instructions based on what you find:

Inspection Finding Required Action Protocol
If there is ink on the ink pad Perform two head-cleaning operations using the Clean function. Then run a nozzle check through Status.
If there is no ink on the ink pad Stop the operation and contact a technician to check the waste ink pipeline.

Do not skip this inspection. Follow the relevant instructions before proceeding with further printer operation. 

Section V. Common Installation Problems to Watch Out For

Improper printhead installation may cause several problems:

  • Poor printing across all colors: The printer may fail to print all colors properly.
  • Missing colors: One or more colors may not print.
  • Continuous ink ejection: The printhead may keep ejecting ink continuously, also known as long ejection.
  • Component damage: In severe cases, the printhead may be damaged, and the motherboard may also be affected.

These risks highlight why correct cable connections, careful handling, and post-installation inspection are essential. If anything appears abnormal, stop and contact Lancelot technical support rather than continuing without guidance.

Section VI. Conclusion & Technical Support

Replacing the printhead on your Lancelot M1630 Pro involves more than removing the old component and installing a new one. Proper white ink system preparation, careful nozzle handling, correct damper placement, accurate cable connections, and post-installation inspection are all essential parts of the process.

Before replacing your printhead, contact our technical support team and follow their instructions for disassembly, installation, and subsequent testing. Taking the right precautions can help prevent unnecessary damage and repair costs.

Looking for a replacement printhead?

👉   DTF Printhead | Replacement Print Head for M1630Pro

Have you ever replaced a DTF printhead yourself? What was the most challenging part of the process? Share your experience in the comments!

Related Posts

Leave a Comment

Your email address will not be published. Required fields are marked *